Telvue HyperCaster® Manuel d'utilisateur télécharger pdf

Getting Started

TelVue HyperCaster

Broadcast Servers

Turn the page for additional steps.

Ethernet [0] Ethernet [1]

Screw in inner rail

to the server

QSG_HC_11_13_V3

B100 models do not need rails. Bolt the ears to your rack. B1000 models need rails as shown.

See the hardware manual that came with your appliance for detailed instructions.

Quick Overview:

• Remove the inner rails from the outer rails. These will need to be permanently attached to the

sides of the server. The inner rail sections will slide out partially, exposing small plastic levers

that need to be depressed in order to fully disengage the inner rails.

• Attach the outer rails to the front of the rack.

• Extend the sliding portion of the outer rails from the rack.

• Align the inner rails of your appliance with outer rails of the rack.

• Slide your appliance into the rack until the rails click into place.

Your appliance includes rails for a standard 19” wide, 32” deep rack. If you are unable to use rails,

TelVue

suggests using rack shelves.

Install your HyperCaster in a Rack

Depending on your model, some TelVue appliances include multiple power supplies. You should plug

in all power supplies for proper redundant operation.

TelVue recommends the use of an Uninterruptible Power Supply (UPS).

Refer to included server hardware manual for safety and environmental information.

Plug in Power and Turn On Unit

There are three methods to set the IP address for your appliance so you can add it to your

network. Each involves making initial settings to the appliance, then logging into the web-based

user interface to complete the setup. Note that out of the box, eth0 is set to DHCP, and eth1 is

set to static IP 192.168.0.240/24 (255.255.255.0). Generally, eth0 should be used for

control, and eth1 for video. Some models have additional eth2 and eth3 options, for either ﬁber

or copper connections.

Method 1: LCD to Conﬁgure Networking

• Press Down and Enter on the LCD to access the menu.

• The up and down arrows can be used to select which device to conﬁgure. Once the

appropriate device has been found, press Enter to continue with the conﬁguration process.

• Select Yes by using the up and down arrows at the DHCP menu to conﬁgure the selected

ethernet device automatically.

• To specify the IP address statically, select No at the DHCP menu and press Enter. Then use

the left and right arrows to select the part of the IP address to modify. Use the up and down

arrows to adjust its value. An underscore will appear below the part of the IP address that is

being modiﬁed.

• Once a valid IP address has been entered, press Enter to accept.

• Conﬁgure the subnet mask and default gateway using the above instructions. Press Enter

after each address has been conﬁgured.

Method 2: Console Login to Conﬁgure Networking

You can access and set the basic networking parameters of your TelVue HyperCaster server by

connecting a keyboard and monitor to the server. All other interactions with the server must be

done through the web interface after the server is integrated into your network.

• Attach a monitor and keyboard to the server.

• Login with username “conﬁg” and password “conﬁg.”

• Choose option 3 to Conﬁgure Networking and set your IP address.

• Reboot using option 6.

Method 3: Web Login to Conﬁgure Networking

Connect a network cable to eth1 and login to the web interface using the default IP:

192.168.0.240. The IP conﬁgurations can be found in the Conﬁg Tab under Server -->

Network. At the login screen enter psgadmin for both username and password.

Add the HyperCaster to Your Network

DHCP – Dynamic Host Conﬁguration Protocol - Your appliance

will acquire an IP address from a DHCP server. This isn’t ideal for

an appliance like your TelVue

broadcast server because your

server may be assigned a new IP address unexpectedly, and it

can be hard to determine what its current IP address is.

Static IP - You set an IP address during conﬁguration and the

appliance always uses that IP address. This is the preferred

method because you always know what the IP address is. You

will need an available IP address on your network, outside the

DHCP range. Contact your IT department to get one.

DHCP Reservation - The reservation tells your DHCP server to

give your appliance the same IP address. This lets you use the

simpler DHCP setup for your appliance, while still letting it use

the same IP address. Refer to your DHCP server’s documentation

to set up a reservation.

IP ADDRESS ASSIGNMENT

16000 Horizon Way, Suite 500

Mount Laurel, NJ 08054

800.885.8886

Email: [email protected]

APIs: http://www.telvue.com/api

Support Portal: Http://www.TelVue.com/support

Training Videos: Http://www.TelVue.com/training

Powering IP Broadcast™

1 2

Getting Started 1
What’s Next? 2

Résumé du contenu

Page 1 - Getting Started

Getting StartedTelVue HyperCaster® Broadcast ServersTurn the page for additional steps. Ethernet [0] Ethernet [1]Screw in inner rail to the serverQSG_

Page 2 - What’s Next?

Getting StartedTelVue HyperCaster® Broadcast Servers16000 Horizon Way, Suite 500Mount Laurel, NJ 08054800.885.8886Email: [email protected]: http:

Plus de documents pour Accessoires pour la télévision Telvue HyperCaster®

Voir le document Telvue HyperCaster® Manuel d'utilisateur

Telvue HyperCaster® Manuel d'utilisateur (105 pages)

Commentaires sur ces manuels

Pas de commentaire

Telvue HyperCaster® Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour la télévision Telvue HyperCaster®. TelVue HyperCaster® User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Accessoires pour la télévision Telvue HyperCaster®

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour la télévision Telvue HyperCaster®